webcam brig belalp valais switzerland webcam birdcam crans-montana valais switzerland webcam berner oberland heimberg bern switzerland webcam berner oberland bern switzerland webcam events brig belalp valais switzerland webcam randogne crans-montana valais switzerland

Docker Swarm mode Deep Dive on Raspberry Pi

Tuesday, 21 March 2017

Getting started with Docker on your Raspberry Pi.

Learn More / Full Story >>

Give your Raspberry Pi a Static IP Address

Monday, 13 March 2017

sudo nano /etc/network/interfaces

/etc/network/interfaces

auto lo
iface lo inet loopback

iface eth0 inet static
address 192.168.5.164
netmask 255.255.255.0
network 192.168.5.0
broadcast 192.168.5.255
gateway 192.168.5.1

Learn More / Full Story >>

Docker Swarm – Clusterize the Docker engines

Saturday, 11 March 2017

Docker Swarm provides native clustering capabilities to turn a group of Docker engines into a single, virtual Docker Engine.

Learn More / Full Story >>

Raspberry Pi – Install TShark sniffing tool

Sunday, 12 February 2017

Prepare Rasbian and install tshark:

Show information and help about tshark:

Learn More / Full Story >>

Raspberry Hot Backup

Saturday, 21 January 2017

#!/bin/bash
# Usage instructions at http://www.megaleecher.net/Best_Raspberry_Pi_Hot_Backup_Shell_Script
# This version disables backup image compression as it takes too much time on Pi, to enable uncomment the relavent lines
# Setting up directories, Just change SUBDIR and DIR varibales below to get going
SUBDIR=raspberrypi_backups
DIR=/media/ExternalHd/$SUBDIR
echo “Starting RaspberryPI backup process!”
# First check if pv package is installed, if not, install it first
PACKAGESTATUS=dpkg -s pv | grep Status;
if [[ $PACKAGESTATUS == S* ]]
then
echo “Package ‘pv’ is installed.”
else
echo “Package ‘pv’ is NOT installed.”
echo “Installing package ‘pv’. Please wait…”
apt-get -y install pv
fi
# Check if backup directory exists
if [ ! -d “$DIR” ];
then
echo “Backup directory $DIR doesn’t exist, creating it now!”
mkdir $DIR
fi
# Create a filename with datestamp for our current backup (without .img suffix)
OFILE=”$DIR/backup_$(date +%Y%m%d_%H%M%S)”
# Create final filename, with suffix
OFILEFINAL=$OFILE.img
# First sync disks
sync; sync
# Shut down some services before starting backup process
echo “Stopping some services before backup.”
service apache2 stop
service mysql stop
service cron stop
# Begin the backup process, should take about 1 hour from 8Gb SD card to HDD
echo “Backing up SD card to USB HDD.”
echo “This will take some time depending on your SD card size and read performance. Please wait…”
SDSIZE=blockdev --getsize64 /dev/mmcblk0;
pv -tpreb /dev/mmcblk0 -s $SDSIZE | dd of=$OFILE bs=1M conv=sync,noerror iflag=fullblock
# Wait for DD to finish and catch result
RESULT=$?
# Start services again that where shutdown before backup process
echo “Start the stopped services again.”
service apache2 start
service mysql start
service cron start
# If command has completed successfully, delete previous backups and exit
if [ $RESULT = 0 ];
then
echo “Successful backup, previous backup files will be deleted.”
rm -f $DIR/backup_*.tar.gz
mv $OFILE $OFILEFINAL
echo “Backup is being tarred. Please wait…”
#tar zcf $OFILEFINAL.tar.gz $OFILEFINAL
# rm -rf $OFILEFINAL
echo “RaspberryPI backup process completed! FILE: $OFILEFINAL”
exit 0
# Else remove attempted backup file
else
echo “Backup failed! Previous backup files untouched.”
echo “Please check there is sufficient space on the HDD.”
rm -f $OFILE
echo “RaspberryPI backup process failed!”
exit 1
fi

Learn More / Full Story >>

Page 1 of 41234